Before choosing a redirect method, clarify whether you are moving old content to a new URL or temporarily showing visitors another page. Then map the old URLs to the new ones and configure the redirects. Once setup is complete, check the results; do not delete the old website simply because the settings have been saved. The guidance below is based on articles published by awoo in 2020 and Welly in 2021. Plugin interfaces and tool features are described as they were at the time and may differ from current versions.
Clarify the purpose before choosing a redirect method
awoo’s article describes using 301 redirects to move old content to a new page and 302 redirects for temporary changes—for example, showing different versions to users visiting the same URL during an A/B test. Before choosing, consider two questions:
- Is this change only temporary? If you plan to restore the original page after a test ends, treat that as a different requirement from a permanent content migration.
- Where should each old URL lead? The article recommends mapping each old URL to a new page with the same content and checking each link individually, rather than merely confirming that a redirect occurs.
The article suggests that thorough URL mapping can help reduce the impact of URL changes on rankings. However, its explanations of how redirects pass ranking signals and preserve rankings reflect the views presented at the time. They do not guarantee that rankings will remain unchanged after a redirect.
Check your version when using a WordPress plugin
If your website uses WordPress, awoo’s 2020 article offers guidance on the Redirection plugin. It noted that the plugin supported 301 and 302 redirects and outlined these basic steps:
- Find Redirection in the plugin list, then install and activate it.
- Open the Redirection settings under “Tools” in the admin sidebar.
- In the redirect settings section, enter the old URL in the source field and the intended new URL in the target field.
For example, the original article demonstrated redirecting /series to /recommend/blackmirrorseason5 on the same website. Make sure you do not mix up the source and target fields. The article also noted that you could enter either a full URL or a path relative to the root directory. These steps describe the version available at the time. Check the fields and status-code options in your version rather than treating these steps as a complete guide to the current interface.
Check that the redirect works and leads to the correct page
Check two things: whether the old URL redirects successfully and whether it leads to the intended page. Merely seeing the page change is not enough to confirm that every old URL has been mapped correctly.
awoo recommended SEO Redirect Checker at the time. Welly’s 2021 article also listed Redirect Checker and mentioned checking status codes through Google Search Console. These methods were listed in the original articles; the tools may not offer the same features today.
Check the redirects before deleting the old website. Welly explicitly emphasized this precaution. Finishing setup alone does not mean it is safe to remove the old site.
Redirect methods: perspectives from across the web
Where should JavaScript redirect code be placed?
Welly’s 2021 article states that JavaScript redirect code can, in principle, be placed anywhere in an HTML page, but recommends placing it in the head section or at the beginning of the page. This is placement advice for cases where JavaScript redirects are used, not a recommendation that every website should use JavaScript. When configuring the redirect, you still need to replace the destination URL with the actual page you want visitors to reach.
Can HTML be used to set up an automatic redirect?
Welly’s 2021 article explains that you can add a meta refresh tag to the head section of an HTML page and specify the delay in seconds and the destination URL. Setting the delay to 0, for example, means the page refreshes and redirects immediately. This is a page-level configuration method. Before using it, confirm that you can edit the page’s HTML, and replace the example URL with the actual destination page.
What needs to be configured for a PHP redirect?
Welly’s 2021 article demonstrates a redirect using PHP’s header() function: specify a 301 or 302 status and use Location to specify the new URL. The example then ends the script with exit(). This method applies to websites that can use PHP. The status code still needs to be chosen according to the purpose of the redirect, and the destination URL must be replaced with the actual page.
References
- 10大轉址服務推薦!教你正確網頁轉址顧好SEO!welly.tw · 2021-12-20T05:18:40.288Z — Discusses: Where should JavaScript redirect code be placed?; Can HTML be used to set up an automatic redirect?
- 301/302轉址如何影響網站SEO?三大要點讓你做好網站SEOwww.awoo.ai · 2020-01-07T09:09:52+00:00 — Source used in the article above.




